Wireless-Devices:WRAP-Board: Difference between revisions
Jump to navigation
Jump to search
Nachtigall (talk | contribs) (howto enable USB in the Bios) |
Nachtigall (talk | contribs) (node table) |
||
| Line 28: | Line 28: | ||
(X) Xmodem upload (Q) Quit |
(X) Xmodem upload (Q) Quit |
||
</code> |
</code> |
||
= List of Nodes = |
|||
{| border="1" |
|||
| <center>'''eth0-MAC'''</center> |
|||
| <center>'''eth0-IP'''</center> |
|||
| <center>'''0<sup>th</sup> wifi MAC'''</center> |
|||
| <center>'''0<sup>th</sup> wifi IP'''</center> |
|||
| <center>'''1<sup>st</sup> wifi-MAC'''</center> |
|||
| <center>'''1<sup>st</sup> wifi IP'''</center> |
|||
| <center>'''misc'''</center> |
|||
|- |
|||
| 00:0D:B9:07:67:88 |
|||
| |
|||
| 00:0C:42:0C:74:2F |
|||
| 10.12.116.47 |
|||
| 00:0C:42:0C:85:9C |
|||
| 10.12.133.156 |
|||
| |
|||
|- |
|||
| 00:0D:B9:05:B4:08 |
|||
| |
|||
| 06:0C:42:0C:74:1B |
|||
| 10.12.116.27 |
|||
| 00:0C:42:0C:85:BB |
|||
| 10.12.133.187 |
|||
| 5 V device with USB |
|||
|- |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
|- |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
|- |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
|- |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
|- |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
| |
|||
|} |
|||
= Links = |
= Links = |
||
Revision as of 10:46, 27 November 2007
Board: PC-Engines WRAP.2E-128
Daughterboard: USB Extension
Enclosure: WRAP-BOX-2A1E
Wireless Card: Wistron CM9
Pigtail
2 Antenna
PoE Adapter
CF-Card: Kingston CF 1GB
Enabling USB
WRAP-Boards with 5V Input
Normally the WRAP-Boards have 12V Input. Anyway, we have one device where the input voltage has been changed to 5V. To enable USB support for this device you must:
- connect USB adapter board to the WRAP-Board
- enable USB support in the BIOS of the WRAP-Board:
- press "S" during memory test when the WRAP-Board boots up to enter the BIOS
- If the menu says "(U)" then this means USB is disabled. Brackets "(U)" mean disabled, and stars "*U*" mean enabled. Press "U" to enable (*U*).
- Press "Q" to quit and the answer Yes to save the settings.
Example
Here the USB is disabled in the BIOS, because it is enclosed by Brackets (press U to change this):
(9) 9600 baud *3* 38400 baud (5) 57600 baud
*C* CHS mode (L) LBA mode
(E) Etherboot enable
(U) USB enable
(D) Conservative DRAM timing
*R* Serial console enable
(X) Xmodem upload (Q) Quit
List of Nodes
| 00:0D:B9:07:67:88 | 00:0C:42:0C:74:2F | 10.12.116.47 | 00:0C:42:0C:85:9C | 10.12.133.156 | ||
| 00:0D:B9:05:B4:08 | 06:0C:42:0C:74:1B | 10.12.116.27 | 00:0C:42:0C:85:BB | 10.12.133.187 | 5 V device with USB | |