Wired Equivalent Privacy

From
Revision as of 12:48, 23 June 2007 by Roman (talk | contribs)
Jump to navigation Jump to search

IEEE 802.11 Standard

The IEEE 802.11 standard that was published 1997 by the Institute of Electrical and Electronics Engineers (IEEE). The standard specifies the two lowest layers of the OSI (Open System Interconnection) model for local wireless networks. This specification of the two layers (Physical & Media Access Control) is kown as WLAN or WIFI. Common protocols like the TCP/IP or ARP operate on top of these two layers.

Osi.png

Basic Service Set

A WLAN consists of a minimum of two communication partners, also called stations. These stations can communicate with each other using electro-magnetic waves, that have a scope of 20m – 300m. This communication area is known as Basic Service Set (BSS). In order to increase the scope of a wireless network, it is common to introduce access points into the network. These access points relay the traffic from stations and thereby increase the overall communication scope. Anyone in the scope of the Basic Service Set can listen to the traffic of the wirless network.

Packet Design

The first part of a packet is unencrypted and contains the 802.11 header, the basic service set identifier, an initialization vector chosen by the sender of the packet and the destination hardware address. The initialization vector is transmitted unencrypted because it is used along with a secret password to initialize a pseudo number generator. The receiver of the packet only knows the secret password, and must be able to initialize the pseudo random number generater with the same value the sender did.

The second part of the packet is encrypted and carries the data of the above protocols like TCP/IP or ARP as well as an CRC32 integrety check value.

The following picture illustrates the design of WEP packet.

Packet.png

Packet Encryption & Decryption

Because anyone can listen to the communication of a wireless network, the IEEE 802.11 includes a cryptographic method to secure the communication between stations and access points. To prevent unauthorized access to the network all packets sent between the communication partners are encrypted. The encryption and decryption of packets is done by using the stream cipher which is explained in the following sections.

Stream Cipher

The stream cipher is used to to encrypt and decrypt packets of arbitrary length. In order to communicate with each other, the sender and reciever have to generate key streams for each packet. The sender uses the XOR operation on the unencrypted packet and the key stream to generate the ciphertext. This ciphertext is sent over the network to the receiver. The receiver on the other side has to generate the same key stream the sender used to encrypt the message. Using the XOR operation again on the ciphertext and the generated key stream results in the plain text.

Streamcipher.png

Encoding

All communication partners that have access to the wireless network share the same secret key KBSS which is used to generate the key stream. If only the secret key KBSS would be used to generate the keystream for a packet, packets with the same content would have the same encrypted representation. Therefore the sender calculates a packet key by choosing a different random initialization vector appended by the secret key KBSS for each packet. This packet key is then used as a seed to initialize the pseudo number generator PRNG, that generates for the same seed always the same key stream. A CRC32 checksum for the plain text is appended to the original message. The message is XOR'ed with the keystream to calculate the ciphertext. Now the encrypted message is ready to be sent to the receiver. Because the reciever also needs to know the initialization vector to compute the seed for the pseudo number generator the encrypted message is sent with the unencrypted initialization vector to the receiver.


Encoding.jpg

Dencoding

When the receiver gets an encrypted packet the unencrypted initialization vector is read from the packet to build the seed for the pseudo number generator along with the secret key KBSS. This seed is the same one the sender used to initialize the pseudo number generator. Then the ciphertext gets XOR'ed with the key stream from the pseudo number generator which results in the plain text message. A CRC32 checksum is calculated from the unencrypted message and verified against the checksum sent with the packet to ensure the packet has not been modified or corrupted.

Decoding.jpg

References