Serial console - Revision history

Henryk at 23:00, 16 April 2006

2006-04-16T23:00:48Z

← Older revision		Revision as of 23:00, 16 April 2006
Line 37:		Line 37:
	[[Image:Wgt_kabel_dran.jpg\|Kabel dran]]		[[Image:Wgt_kabel_dran.jpg\|Kabel dran]]
	</li>		</li>

			==More elegant solution==
			The female end of a molex extension such as that used for processor fans (ADAPTER 3/3 30CM at Reichelt) will nicely fit on the WGT's connector and the individual wires can be fed through the ventilation holes onto the outside. This enables access to the serial port while the WGT's case is closed. You need two such extension cords, or rather: two female ends and one male end. One female end goes onto the WGT, one male end is dangling outside the WGT and one female end is connected to the serial cable.

			By pure coincidence said molex connector fits almost exactly into the available space (with about a millimeter of room left).

			<ol>
			<li>Cut each molex cable in two.</li>
			<li>Put one female end onto the serial connector in the WGT. There are only three signals in the cable (while the serial connector has four) but you'll only need TX, RX and GND anyways. Hint: in order to enhance interoperability use the black wire for GND.</li>
			<li>Thread the wires through the WGT's ventilation holes on the upper side. Make sure you choose the right holes, so that you can close the case without bending the port or the connector:<br>
			[[Image:Wgt_seite.jpg]]<br>
			[[Image:Wgt_oben.jpg]]</li>
			<li>Reconnect one male end to the cable (maybe shorten it a little), and close the WGT.<br>
			[[Image:Wgt_fertig.jpg]]</li>
			<li>Connect the remaining female end similar to the other instructions above:<br>
			[[Image:Serial_cable.jpg]]</li>
			</ol>

			No you can connect and disconnect the serial cable to your WGT at will, without opening it. And if need be you can undo all your modifications, because the hardware or case has not been changed.<br>
			Bonus: The serial cable itself will fit an unmodified WGT (with open case, of course).

Henryk: clean up

2006-04-16T22:38:08Z

clean up

← Older revision		Revision as of 22:38, 16 April 2006
Line 1:		Line 1:
	Serialkabel/Serial Connector für/for [http://www.netgear.com/products/details/WGT634U.php WGT634U]		Serialkabel/Serial Connector für/for [http://www.netgear.com/products/details/WGT634U.php WGT634U]

	Tools~~:<br>~~		==Tools==
	*Torxschraubendreher/screwdriver T 8~~<br>~~		*Torxschraubendreher/screwdriver T 8
	*Knipex, or any other wire cutting pliers~~<br>~~		*Knipex, or any other wire cutting pliers
	*Lötkolben/soldering iron~~<br>~~		*Lötkolben/soldering iron
	*Schrumpfschlauch/shrinkable tubing~~<br>~~		*Schrumpfschlauch/shrinkable tubing

	<br>
	~~<b>~~Einkaufsliste/Shopping list~~:</b><br>~~		==Einkaufsliste/Shopping list==
	<br>		<ul>
		⚫	<li>[[Image:Buchsenleiste_abgeschnitten.jpg\|thumbnail\|Buchsenleiste abgeschnitten]]
⚫	- BL ~~1X20W~~ 2,54 - ~~20pol~~. Buchsenleiste, ~~gewinkelt~~, RM (Rastermaß) 2,54 (-> www.reichelt.de) or<br>
	- BL ~~1X10G~~ 2,54 - ~~10pol~~. Buchsenleiste, ~~gerade~~, RM (Rastermaß) 2,54 (-> www.reichelt.de)<br>		<ul><li>BL 1X20W 2,54 - 20pol. Buchsenleiste, gewinkelt, RM (Rastermaß) 2,54 (-> www.reichelt.de) or</li>
		⚫	<li>BL 1X10G 2,54 - 10pol. Buchsenleiste, gerade, RM (Rastermaß) 2,54 (-> www.reichelt.de)<br>
	<br>
	(es werden nur vier Pings benötigt/you need only four pins -> Knipex, eine Seite mit Lötkolben markiert/one side marked with soldering iron)		(es werden nur vier Pings benötigt/you need only four pins -> Knipex, eine Seite mit Lötkolben markiert/one side marked with soldering iron)</li></ul>
			</li>
⚫	[[Image:Buchsenleiste_abgeschnitten.jpg\|Buchsenleiste abgeschnitten]]~~<br>~~
			<li style="clear:both">
	<br>
		⚫	[[Image:S25_kabel.jpg\|thumbnail\|S25 Datenkabel]]
	- DATENKABEL S25 - für alle Siemens C/M/S 25/35/45 (enthält Pegelwandler/contains level converter (5V->3.3V))<br>		DATENKABEL S25 - für alle Siemens C/M/S 25/35/45 (enthält Pegelwandler/contains level converter (5V->3.3V)) </li>
⚫	[[Image:S25_kabel.jpg\|S25 Datenkabel]]
			</ul>
	<br><br><b>To do list</b><br>
			<br style="clear:both">
	<br>
			==To do list==
⚫	- Der Stecker des Kabel (Telefonseite) muss gehöffnet werden/You have to open the plug which is intended to be used with the mobile phone.<br>
	<br>		<ol>
		⚫	<li>Der Stecker des Kabel (Telefonseite) muss gehöffnet werden/You have to open the plug which is intended to be used with the mobile phone.<br>
	davor/before:<br>		davor/before:<br>
	[[Image:S25_stecker_geschlossen.jpg\|Stecker geschlossen]]<br>		[[Image:S25_stecker_geschlossen.jpg\|Stecker geschlossen]]<br>
	<br>		<br>
	danach/after (red cable is not connected, colouring can differ):<br>		danach/after (red cable is not connected, colouring can differ):<br>
	[[Image:S25_stecker_offen.jpg\|Stecker offen]]<br>		[[Image:S25_stecker_offen.jpg\|Stecker offen]]<br></li>
		⚫	<li> Stecker entfernen und Farbbelegung merken/Remove the plug and remember the colour mapping. Siehe hier für Details/Look here for details [http://www.nobbi.com/steck_s25.htm pin mapping] (DATA OUT=TX, DATA IN=RX)<br>
	<br>
⚫	- Stecker entfernen und Farbbelegung merken/Remove the plug and remember the colour mapping. Siehe hier für Details/Look here for details [http://www.nobbi.com/steck_s25.htm pin mapping] (DATA OUT=TX, DATA IN=RX)<br>
	<br>1 = GND, 5 = DATA OUT, 6 = DATA IN<br>		<br>1 = GND, 5 = DATA OUT, 6 = DATA IN<br>
	[[Image:S25_loet.png\|Schema]]<br>		[[Image:S25_loet.png\|Schema]]<br>
	[[Image:S25_stecker_ab.jpg\|Stecker ab]]		[[Image:S25_stecker_ab.jpg\|Stecker ab]]</li>
		⚫	<li> Kabel an die richtigen Pins anlöten und den Schrumpfschlauch zur Isolation benutzen/Solder the cables to the appropriate pins of the socket board and use the shrinkable tubing as insulation<br>
	<br>
		⚫	[[Image:Buchsenleiste_geloetet.jpg\|Buchsenleiste angeloetet]]</li>
⚫	<br>- Kabel an die richtigen Pins anlöten und den Schrumpfschlauch zur Isolation benutzen/Solder the cables to the appropriate pins of the socket board and use the shrinkable tubing as insulation<br>
		⚫	<li> fertiges Kabel an den WGT anschließen/Connect your customized cable to the WGT<br>
⚫	[[Image:Buchsenleiste_geloetet.jpg\|Buchsenleiste angeloetet]]<br>
	<br>
⚫	- fertiges Kabel an den WGT anschließen/Connect your customized cable to the WGT<br>
	[[Image:Wgt_offen.jpg\|WGT offen]]		[[Image:Wgt_offen.jpg\|WGT offen]]
	[[Image:Wgt_kabel_dran.jpg\|Kabel dran]]		[[Image:Wgt_kabel_dran.jpg\|Kabel dran]]
			</li>

Cakruege at 20:03, 9 March 2006

2006-03-09T20:03:23Z

← Older revision		Revision as of 20:03, 9 March 2006
Line 1:		Line 1:
	~~Serielle Kabel~~/Serial Connector für/for [http://www.netgear.com/products/details/WGT634U.php WGT634U]		Serialkabel/Serial Connector für/for [http://www.netgear.com/products/details/WGT634U.php WGT634U]

	Tools:<br>		Tools:<br>

Cakruege at 20:02, 9 March 2006

2006-03-09T20:02:55Z

← Older revision		Revision as of 20:02, 9 March 2006
Line 1:		Line 1:
	Serial Connector für/for [http://www.netgear.com/products/details/WGT634U.php WGT634U]		Serielle Kabel/Serial Connector für/for [http://www.netgear.com/products/details/WGT634U.php WGT634U]

	Tools:<br>		Tools:<br>

Cakruege at 12:54, 22 February 2006

2006-02-22T12:54:02Z

← Older revision		Revision as of 12:54, 22 February 2006
Line 7:		Line 7:
	*Schrumpfschlauch/shrinkable tubing<br>		*Schrumpfschlauch/shrinkable tubing<br>
	<br>		<br>
	<b>Shopping list:</b><br>		<b>Einkaufsliste/Shopping list:</b><br>
	<br>		<br>
	- BL 1X20W 2,54 - 20pol. Buchsenleiste, gewinkelt, RM 2,54 (-> www.reichelt.de) or<br>		- BL 1X20W 2,54 - 20pol. Buchsenleiste, gewinkelt, RM (Rastermaß) 2,54 (-> www.reichelt.de) or<br>
	- BL 1X10G 2,54 - 10pol. Buchsenleiste, gerade, RM 2,54 (-> www.reichelt.de)<br>		- BL 1X10G 2,54 - 10pol. Buchsenleiste, gerade, RM (Rastermaß) 2,54 (-> www.reichelt.de)<br>
	<br>		<br>
	(you need only four pins -> Knipex, one side marked with soldering iron)~~<br>~~		(es werden nur vier Pings benötigt/you need only four pins -> Knipex, eine Seite mit Lötkolben markiert/one side marked with soldering iron)
	[[Image:Buchsenleiste_abgeschnitten.jpg\|Buchsenleiste abgeschnitten]]<br>		[[Image:Buchsenleiste_abgeschnitten.jpg\|Buchsenleiste abgeschnitten]]<br>
	<br>		<br>

Cakruege at 12:52, 22 February 2006

2006-02-22T12:52:28Z

Efuhrman at 21:50, 8 January 2006

2006-01-08T21:50:29Z

← Older revision		Revision as of 21:50, 8 January 2006
Line 19:		Line 19:
	<br><br><b>To do list</b><br>		<br><br><b>To do list</b><br>
	<br>		<br>
	- You have to open the plug which is intended to ~~use~~ with the mobile phone.<br>		- You have to open the plug which is intended to be used with the mobile phone.<br>
	<br>		<br>
	before:<br>		before:<br>

Cakruege at 21:16, 8 January 2006

2006-01-08T21:16:30Z

← Older revision		Revision as of 21:16, 8 January 2006
Line 19:		Line 19:
	<br><br><b>To do list</b><br>		<br><br><b>To do list</b><br>
	<br>		<br>
	- You have to open the ~~mobile~~ ~~phone~~ ~~side~~ ~~plug~~.<br>		- You have to open the plug which is intended to use with the mobile phone.<br>
	<br>		<br>
	before:<br>		before:<br>

Cakruege at 21:15, 8 January 2006

2006-01-08T21:15:07Z

← Older revision		Revision as of 21:15, 8 January 2006
Line 34:		Line 34:
	<br>- Solder the cables to the appropriate pins of the socket board and use the shrinkable tubing as insulation<br>		<br>- Solder the cables to the appropriate pins of the socket board and use the shrinkable tubing as insulation<br>
	[[Image:Buchsenleiste_geloetet.jpg\|Buchsenleiste angeloetet]]<br>		[[Image:Buchsenleiste_geloetet.jpg\|Buchsenleiste angeloetet]]<br>
			<br>
	- Connect your customized cable to the WGT<br>		- Connect your customized cable to the WGT<br>
	[[Image:Wgt_offen.jpg\|WGT offen]]		[[Image:Wgt_offen.jpg\|WGT offen]]

Cakruege at 21:14, 8 January 2006

2006-01-08T21:14:34Z

← Older revision		Revision as of 21:14, 8 January 2006
Line 28:		Line 28:
	<br>		<br>
	- Remove the plug and remember the colour mapping. Look here for details [http://www.nobbi.com/steck_s25.htm pin mapping] (DATA OUT=TX, DATA IN=RX)<br>		- Remove the plug and remember the colour mapping. Look here for details [http://www.nobbi.com/steck_s25.htm pin mapping] (DATA OUT=TX, DATA IN=RX)<br>
	<br>
	<br>1 = GND, 5 = DATA OUT, 6 = DATA IN<br>		<br>1 = GND, 5 = DATA OUT, 6 = DATA IN<br>
	[[Image:S25_loet.png\|Schema]]<br>		[[Image:S25_loet.png\|Schema]]<br>

← Older revision		Revision as of 12:52, 22 February 2006
Line 1:		Line 1:
	Serial Connector for WGT634U		Serial Connector für/for [http://www.netgear.com/products/details/WGT634U.php WGT634U]

	Tools:<br>		Tools:<br>
Line 15:		Line 15:
	[[Image:Buchsenleiste_abgeschnitten.jpg\|Buchsenleiste abgeschnitten]]<br>		[[Image:Buchsenleiste_abgeschnitten.jpg\|Buchsenleiste abgeschnitten]]<br>
	<br>		<br>
	- DATENKABEL S25 - für alle Siemens C/M/S 25/35/45 (contains level converter ~~(Pegelwandler)~~ (5V->3.3V))<br>		- DATENKABEL S25 - für alle Siemens C/M/S 25/35/45 (enthält Pegelwandler/contains level converter (5V->3.3V))<br>
	[[Image:S25_kabel.jpg\|S25 Datenkabel]]		[[Image:S25_kabel.jpg\|S25 Datenkabel]]
	<br><br><b>To do list</b><br>		<br><br><b>To do list</b><br>
	<br>		<br>
	- You have to open the plug which is intended to be used with the mobile phone.<br>		- Der Stecker des Kabel (Telefonseite) muss gehöffnet werden/You have to open the plug which is intended to be used with the mobile phone.<br>
	<br>		<br>
	before:<br>		davor/before:<br>
	[[Image:S25_stecker_geschlossen.jpg\|Stecker geschlossen]]<br>		[[Image:S25_stecker_geschlossen.jpg\|Stecker geschlossen]]<br>
	<br>		<br>
	after (red cable is not connected, colouring can differ):<br>		danach/after (red cable is not connected, colouring can differ):<br>
	[[Image:S25_stecker_offen.jpg\|Stecker offen]]<br>		[[Image:S25_stecker_offen.jpg\|Stecker offen]]<br>
	<br>		<br>
	- Remove the plug and remember the colour mapping. Look here for details [http://www.nobbi.com/steck_s25.htm pin mapping] (DATA OUT=TX, DATA IN=RX)<br>		- Stecker entfernen und Farbbelegung merken/Remove the plug and remember the colour mapping. Siehe hier für Details/Look here for details [http://www.nobbi.com/steck_s25.htm pin mapping] (DATA OUT=TX, DATA IN=RX)<br>
	<br>1 = GND, 5 = DATA OUT, 6 = DATA IN<br>		<br>1 = GND, 5 = DATA OUT, 6 = DATA IN<br>
	[[Image:S25_loet.png\|Schema]]<br>		[[Image:S25_loet.png\|Schema]]<br>
	[[Image:S25_stecker_ab.jpg\|Stecker ab]]		[[Image:S25_stecker_ab.jpg\|Stecker ab]]
	<br>		<br>
	<br>- Solder the cables to the appropriate pins of the socket board and use the shrinkable tubing as insulation<br>		<br>- Kabel an die richtigen Pins anlöten und den Schrumpfschlauch zur Isolation benutzen/Solder the cables to the appropriate pins of the socket board and use the shrinkable tubing as insulation<br>
	[[Image:Buchsenleiste_geloetet.jpg\|Buchsenleiste angeloetet]]<br>		[[Image:Buchsenleiste_geloetet.jpg\|Buchsenleiste angeloetet]]<br>
	<br>		<br>
	- Connect your customized cable to the WGT<br>		- fertiges Kabel an den WGT anschließen/Connect your customized cable to the WGT<br>
	[[Image:Wgt_offen.jpg\|WGT offen]]		[[Image:Wgt_offen.jpg\|WGT offen]]
	[[Image:Wgt_kabel_dran.jpg\|Kabel dran]]		[[Image:Wgt_kabel_dran.jpg\|Kabel dran]]